Design guide

Speakers as part of the interior: visible, flush-mounted and invisible audio with KNX and Loxone

In a smart-home project the speaker is an architectural decision first and a product choice second. Below: three strategies for the room, how Ekinex, Loxone and Basalte implement them, and what structure, rack and finish must provide before cabling starts.

Updated: 20 November 2026 · PanelCraft
In short
  • Three strategies: speaker as an object (Basalte Aalto and Rondo, Ekinex Iride and Omni), flush with a grille or fabric (Basalte Plano and Cielo, Loxone Install Speaker, Ekinex built-in speakers) and invisible (Ekinex Invisible DRYWALL, GLASS, WOOD, TWIN).
  • Plaster-in invisible panels tolerate only 1.5-3 mm of finish, depending on the brand, and none of the manufacturers we checked lists tile as a covering.
  • Loxone Audioserver delivers 18 W RMS per channel on 4 outputs; 50 W is the peak figure. Ekinex exposes Sentio zones to KNX through the EK-BS1-TP gateway.
  • Everything that cannot be changed later is decided before finishing: cable route, installation housing, ceiling and wall build-up, amplifier location and its heat.

Three strategies for the room

Decide with the architect how much of the speaker should be seen: that sets the product family, the construction detail and the cable route. The products are from our speakers and amplifiers catalog.

StrategyCatalog productsWhat is visible in the roomRequirements for the building works
Speaker as an objectBasalte Aalto (on-wall, floor-standing, soundbars) and Rondo; Ekinex Iride and Omni floor-standing; Loxone Wall SpeakerA designed body in fabric (Gabriel, Kvadrat), metal or lacquerPower or speaker cable at the position, wall fixing or stand
Flush with grille or fabricBasalte Plano (fabric front) and Cielo (paintable grille); Loxone Install Speaker 7/10; Ekinex Q10CG, Q15CG, T18CG (plasterboard) and Q15M (masonry)A grille or fabric panel in the plane of the wall or ceilingInstallation housing before finishing (drywall or concrete version), cut-out size, ceiling void depth
InvisibleEkinex Invisible DRYWALL, GLASS, WOOD, TWIN with POWER 1 amplifierNothing: the finished surface playsMaterial and thickness within the emitter's limits, depth behind the surface, a gap behind wood panels, subwoofer for bass

Three systems compared by architecture and confirmed figures

LoxoneEkinexBasalte
Source and serverAudioserver: 4 speaker outputs, line-in, line-out, SPDIF out, LAN, USBSentio streamers: 30 W, 50 Wx2, 80 Wx2, or 50 Wx8 for 4 zonesCore servers (Core Plus for multiroom, Core Mini for basic control) and Asano multiroom amplifiers
AmplificationClass D, 4 to 8 ohm, 18 W RMS x4 (50 W peak); Stereo Extension adds one stereo output, up to 10 per AudioserverPOWER 1 for Invisible: 200 W RMS mono at 4 ohm or 80 W RMS x2; built-in amplifiers in streamersAsano amplifiers; channel and watt figures are partner-only documentation, so we do not quote them
SpeakersInstall Speaker 7 and 10 (Master, Client, Passive), Wall, Satellite IP64, WirelessLaboratorio Audio series, Classic, Invisible Player, subwoofersAalto, Plano, Rondo, Cielo
ControlLoxone Miniserver logic; AirPlay 2 and Spotify Connect; doorbell, alarm and announcements on the same speakersSentio app; KNX-Sentio Gateway EK-BS1-TP for KNXBasalte Home app, keypads and remotes

The Ekinex gateway exposes each Sentio zone to KNX: volume, bass and treble, play and pause, mute, track skip, source preset, artist and title. Compare the systems by purpose and project fit, not by rank. Brand pages: Loxone, Ekinex and Basalte.

Sourcesstreaming, radio, TV, doorbellAudio server / streamerin the rack or panelMultiroom amplifierin the rack or panelLiving roomKitchenBathroomTerraceControl: wall keypad, app, scenesKNX / Loxone
Multiroom chain: sources, audio server, amplifier in the rack or panel, then zone speakers, with KNX or Loxone control on top.

Invisible speakers and finishing materials

An invisible speaker is an exciter fixed behind a surface that makes the surface itself sound. Ekinex states the following for its Invisible Player line.

  • DRYWALL EK-DW1-AU: plasterboard walls and ceilings up to 16 mm, up to 80 m2 per emitter, 120 W max, 40 W RMS, 40-14,000 Hz, 4 ohm, glued with EK-3M77-AU; Vertfix EK-VFX-AU holds it in vertical walls.
  • GLASS EK-GL1-AU: glass and non-porous materials (e-bond, acrylic, lexan, fibreglass) up to 12 mm.
  • WOOD EK-WO1-AU: wood 18-25 mm; not for surfaces fixed to the floor or wall, and a gap of a few millimetres is needed behind.
  • TWIN EK-TW1-AU: double transmitter, 240 W max, 80 W RMS, 40-15,000 Hz, 8 ohm, 160 x 80 mm plate.

Plaster-in panels from other brands are a different technology: the panel is skimmed into the wall, and each brand sets its own finish-layer limit.

BrandFinish layer limitCoverings named
Amina2 mm skim; more than 2-3 mm may affect performancePlasters, microcement, veneer, thin stone, leather, fabric, HPL
Stealth AcousticsCompound is optional, at most 1/16 in (1.5 mm)Four coats of latex paint or light wallpaper; rough textures not recommended
Sonance InvisibleUp to 3 mm of topping compoundDrywall, some plasters, wallpaper, leather, veneer
NakymatoneWithin 1/16 in (about 1.5 mm)Plaster, wallpaper, laminate, leather, thin wood; not thick stone walls or dense insulation behind
Tip: None of the checked manufacturers lists ceramic or porcelain tile as a covering; thin stone veneer is declared by Amina only. We found no direct approval for wet rooms either. Have a non-standard finish tested by the manufacturer.
roomcavity behind the wallamplifierfinish: paint, thin plaster, veneersurface that sounds: drywall, glass or woodtransmitter (exciter) fixed behind
Section of an invisible speaker: finish, sounding surface, the exciter fixed behind it, and the amplifier located elsewhere.

Designer's checklist by project stage

  1. Concept with the architect. Pick a strategy per room and mark on the ceiling plan where grilles are allowed. Loxone plans one speaker per 15 m2 in living rooms with standard ceiling height.
  2. Cable schedule and housings before finishing. Number every speaker line and route it to the amplifier; Loxone outputs take passive 4-8 ohm speakers and cable up to 2.5 mm2. Order the installation housings and frames (drywall or concrete versions) before the slab is poured or the boards are closed.
  3. Amplifier position, heat and power. Amplifiers go in the rack or panel with ventilation and a power budget: at least 72 W per Audioserver and 36 W per Stereo Extension, with a separate supply recommended. Tree Turbo takes up to 10 devices per interface and 150 m of cable; it is IP-based and must not be joined to standard Tree.
  4. Commissioning and scenes. Assign zones, check the polarity of every channel, set the equaliser, then map volume and source to KNX group addresses or Loxone blocks.

Typical project mistakes

  • Plano specified as paintable (its front is fabric) or Cielo as fabric (its grille is paintable).
  • A plaster-in panel under a layer thicker than the brand limit, under tile or a heavy texture.
  • Invisible WOOD on a panel fixed to the wall or floor, with no gap behind it.
  • Loxone outputs sized by the 50 W peak figure instead of 18 W RMS per channel.
  • Outdoor zones planned without checking the IP rating: Install Speaker 7/10 are IP53/54, Satellite Speaker IP64, the Ekinex on-wall pair IP66. See outdoor audio.

Frequently asked questions

Can invisible speakers be installed behind tile?

None of the manufacturers we checked lists tile as a covering, so we do not specify it. They name plaster, microcement, veneer, wallpaper, leather and similar thin finishes, within 1.5-3 mm depending on the brand.

What is the difference between Basalte Plano and Cielo?

Plano is a passive in-wall speaker with a fabric front (Gabriel or Kvadrat). Cielo is a passive in-ceiling speaker with a round or square paintable white grille in three sizes.

Is there a KNX interface for Ekinex multiroom audio?

Yes. The KNX-Sentio Gateway EK-BS1-TP (DIN rail, 2 modules, KNX TP and Ethernet) finds the Sentio zones itself and gives each zone group addresses for volume, tone, playback, mute, track and source.

How many zones can one Loxone Audioserver drive?

One Audioserver has 4 speaker outputs: two stereo zones, or the outputs split into separate channels. Each Stereo Extension adds one stereo output, up to 10 per Audioserver; several Audioservers can be combined, and Loxone states no numeric zone limit.

Do invisible speakers need a subwoofer?

Plan for one: bass from a sounding surface is limited, and Ekinex, Sonance, Nakymatone and Cerasonar offer subwoofers. Ekinex lists the built-in passive Q5.5SUB (100 W, 40-150 Hz) and Q6.6SUB (130 W, 35-120 Hz).

Plan the audio before finishing starts

Send the plans and the interior concept. We will propose a strategy per room, housings, a cable schedule and the amplifier location.

Request a project

Read next

Loading...
Back to top